谈用三爪卡盘装夹车削钢件时的切削用量

指出根据《金属切削手册》给出的切削用量范围确定切削用量，有可能不适当，特别是在三爪卡盘装夹硬度低的半径小的工件时容易发生这种情况，提出根据工件硬度、夹持长度、三爪的夹持半径等诸因素确定切削用量的方法。     

ESW激波吹灰器在余热锅炉的应用

介绍了ESW激波吹灰器的工作原理及其在茂名分公司Ⅲ套催化裂化装置余热锅炉的应用情况。应用结果表明，使用ESW激波吹灰器吹灰效果明显，吹灰后余热锅炉排烟温度可下降29℃，过热蒸汽产量增加7t/h，锅炉自产饱和蒸汽产量增加2t/h，有效提高了余热锅炉的传热效率和过热能力，节能效果显著。对应用中出现的一些问题提出了改进建议。     

Use of zeolite-rich rocks and waste materials for the production of structural lightweight concretes

This paper aims at testing the use of mixtures constituted by natural zeolitized products and SiC-bearing industrial wastes (sludge deriving from polishing of porcelain stoneware tiles, hereafter DPM) for the production of lightweight expanded aggregates as constituents of structural and/or thermo-insulating lightweight concretes. Two commercial products have been used as zeolite natural source: Cab70 (Yellow facies of Campanian Ignimbrite) and IZclino (Turkish clinoptilolite-rich epiclastite). Different amounts of a calcareous material (Pozzano limestones — hereafter CP) from the Sorrento peninsula (Naples — Italy) were also added to a Cab70–DPM mixture. All raw materials were characterized by means of mineralogical (XRPD) and chemical (XRF) analyses. All the products and mixtures were tested from a technological point of view by means of fusibility and firing tests in order to evaluate the expanding properties. It was evidenced that the expansion of the mixture was deeply depending on the occurrence of SiC in the industrial waste. The addition of CP (10 wt.%) to the mixtures accounts for an even increased expansion, though this is accompanied by a worsening of the mechanical features of the material.These results along with literature data allowed to select 3 mixtures (70% Cab70–30% DPM, 70% IZclino–30% DPM, 60% Cab70–30% DPM–10% CP) and each of them was used for the preparation of 5 l of lightweight aggregates afterward employed for the manufacture of lightweight concretes. It was remarked that natural zeolitized materials mixed with DPM (30 wt.%) can provide lightweight aggregates with densities ranging between 0.8 and 1.0 g/cm³ suitable for the preparation of structural lightweight concretes. The addition to the mixture of CP (10 wt.%) produces less dense aggregates (0.6–0.7 g/cm³) potentially useful for the manufacture of thermo insulating lightweight concretes.     

复杂环境下超长深基坑工程实例研究

深基坑工程长近百米，周边环境复杂，施工作业条件差，结合工程设计留设的后浇带，采用适合的支护结构体系、止水帷幕技术、土方开挖方法，加强施工监测，着力于减少对周边环境的不利影响，为类似条件的深基坑工程的施工提供了有益的经验。     

利用废硅胶生产五水偏硅酸钠的研究

概述了五水偏硅酸钠的市场现状,介绍了以废硅胶为原料生产五水偏硅酸钠的实验方法。通过实验,得出了优化实验条件为:模数采用0.5~0.8,波美度在35~50°,加热废硅胶及浓缩结晶的温度为90~100℃,时间为持续沸腾5min以上,采用自然降温法,时间在10h左右。最终制得良好的晶体,其中氧化钠含量为28.5%,氧化硅含量27.3%,产品质量达到国内同类产品的一级品标准。     

水吸收-催化燃烧技术处理PET聚酯废气的中试研究

应用水吸收—催化燃烧技术处理PET聚酯生产中排放的含乙二醇、2—甲基—1，3—二氧戊环、乙醛等废气。水吸收可以有效脱除高沸点的乙二醇，通过对乙醛的吸收、解吸作用使废气的总烃浓度得到均匀化处理；采用Pt／Pd／CeO2蜂窝状催化剂，在反应器床层空速40000h^-1，人口温度250℃，人口总烃浓度3522—5666μL/L的条件下，反应器出口总烃浓度54—84μL/L，乙醛浓度3—11μL/L，总烃去除率达到97．6％一98．9％，净化后气体符合国家排放标准。     

焦粉四辊破碎机高硬度辊皮切削的新工艺

分析了高硬度辊皮的磨损情况；改进了辊皮的切削方案；满足了生产需求并提高了作业率。     

含过期火药粉状工业炸药的研究

文章概要论述了一种新型民用炸药－含过期火药粉状工业炸药在配方、制造工艺等方面所进行的实验研究。结果表明，该炸药性能良好、制造技术安全可靠，值得推广。     

四坐标数控加工原理及算法研究

本文对四坐标数控加工原理和算法作了详细介绍，尤其对四坐标加工的刀轴矢量算法进行了研究，提出了用垂直于回转轴的平面与刀具运动方向和前导角形成的圆锥面求交，生成刀轴矢量的方法，该方法具有立意新颖、思路清晰，性能可靠，易于在微机上实现等特点，对复杂曲面零件的加工编程，具有重要的实用价值。     

筛前神经及下鼻甲激光切割术治疗过敏性鼻炎29例临床观察

本文介绍了用筛前神经和下鼻甲激光切割术治疗２９例过敏性鼻炎病人，有效率为９７％。随访６个月至２年，除２例于术后６个月复发外，余者均未复发。实践表明这一手术优于翼管神经手术，优点是：１、解剖标志清楚；２、手术操作简便且易于掌握；３、并发症少而不严重。本文对这一手术的方法，术后处置和疗效进行了讨论。